Atlas Copco 2911012000 Rotor Installation Maintenance Kit là phụ tùng chính hãng Atlas Copco do Á Đông Group phân phối tại Việt Nam. Sản phẩm cam kết 100% chính hãng (Original Genuine), phù hợp thay thế theo đúng mã, giao hàng nhanh và hỗ trợ kỹ thuật tra cứu mã phụ tùng.
Atlas Copco 2911012000 Rotor Installation Maintenance Kit là phụ tùng chính hãng Atlas Copco do Á Đông Group phân phối tại Việt Nam. Sản phẩm cam kết 100% chính hãng (Original Genuine), phù hợp thay thế theo đúng mã, giao hàng nhanh và hỗ trợ kỹ thuật tra cứu mã phụ tùng.
| Thương hiệu | Atlas Copco |
| Mã phụ tùng (SKU) | 10898 |
| Delivery Time | 3-5 Days |
| MOQ | 1 Pcs |
| Package | Original Package |
| Packaging Details | Carton |
| Place of Origin | MT |
| Product Quality | 100% Original Genuine, 100% Original Parts |
| Mã phụ tùng | Loại |
|---|---|
| 2911012000 | Phụ tùng Atlas Copco chính hãng |
The Atlas Copco 2911012000 rotor installation maintenance kit measures 400 × 22 × 400 mm and weighs 322 g. Atlas Copco builds it for oil-injected rotary screw air compressors , and it carries the gaskets and seals you need for a clean rotor fit. Reach for it whenever you fit or refit the compression rotor or airend during planned service.
What the 2911012000 Rotor Installation Kit Delivers
This kit gives you a genuine Atlas Copco service part, not a loose pile of shop seals. Every gasket follows the airend s mating face, so the rotor drops in without hand-fitting or trimming. A poor seal at the rotor housing lets oil and air mix where they shouldn t, and that failure usually surfaces only after you have closed everything back up.
Most rotor-work failures start with a reused or wrong gasket, which is exactly the guesswork this kit removes. You open the box and fit the parts in the order they belong. Then you close the airend and restore the original tolerances.
Atlas Copco ELEMENT MOUNTING KIT 2911012000 (1)
When to Fit the Rotor Installation Maintenance Kit
Use this kit during a scheduled overhaul or a rotor exchange — basically any time the compression element leaves the compressor frame. It is the right call when the airend comes off the bedplate and the mating faces sit exposed.
The same kit also handles rotor refitting after a bearing change or a rotor reconditioning visit. In every case the goal stays the same: seal the rotor housing so the machine returns to service without leaks. If your site runs several oil-injected screw units on a service plan, keep one on the shelf.
Inside the Kit and How It Supports Rotor Fitting
A rotor installation kit centers on the large airend gasket plus the smaller seals that close the rotor cavity. Because Atlas Copco ships them as a matched set, the flat gasket and the ring seals share the same rotor drawing. You avoid mixing grades or stretching a seal never meant for that face.
Fit the main gasket first, seat the rotor, then close up with the supplied seals. Take the torque to the figure in the machine s manual rather than by feel. A clean, even clamp keeps the joint from weeping once the compressor goes back under pressure.
Atlas Copco ELEMENT MOUNTING KIT 2911012000 (2)
Technical Specifications
Attribute
Value
Part number
2911012000
Product
Rotor installation maintenance kit
For compressor
Oil-injected rotary screw air compressors
Dimensions (W × H × L)
400 × 22 × 400 mm
Weight
322 g
Origin
Installing the Rotor with the 2911012000 Kit
Start by cleaning both mating faces; old gasket still on the surface will stop the new one from seating. Lay the gasket flat, lower the rotor squarely, and check it sits without twisting. Then fit the seals in the order the kit implies.
Do not reuse the old gasket as a stop-gap. A reused seal causes most leaks after rotor work, and it adds far more downtime than the kit itself. Close the airend, torque to manual spec, and run a short test before the unit returns to full load.
Atlas Copco ELEMENT MOUNTING KIT 2911012000 (3)
FAQ
What is the Atlas Copco 2911012000 used for?
This kit supplies the gaskets and seals you need to fit or refit the compression rotor or airend on an oil-injected rotary screw compressor during service.
Which compressors does the rotor installation kit fit?
Atlas Copco builds it for oil-injected rotary screw air compressors where you install or exchange the rotor or airend. Confirm the exact match against your machine s parts book or serial nu
Á Đông Group – Nhà phân phối phụ tùng máy nén khí Atlas Copco chính hãng tại Việt Nam. Tư vấn kỹ thuật, hỗ trợ tra cứu mã phụ tùng, giao hàng nhanh & bảo hành toàn quốc. Website: sullivan-palatek.vn
